CISCO LINKSYS WRT54GH FIRMWARE DOWNLOAD UPGRADE
CISCO LINKSYS WRT54GH FIRMWARE DOWNLOAD FULL
CISCO LINKSYS WRT54GH FIRMWARE DOWNLOAD PASSWORD

I will use some of the text from those instructions as well as inserting my screenshots and other encounters not mentioned in the above link. Following the instructions found at Steps_to_flash_through_Web_Interface, I was eventually successful in getting DD-WRT installed. I tried to take screenshots of each step as I went, so as not to confuse anyone. The following are the steps that I went through to get DD-WRT v23 installed on a WRT54G v4 (or WRT54GL). (Remember to hold reset button for 30 sec after flashing mini version.) The stock firmware from Linksys on the WRT54G v4 won't accept a firmware image over 3MB in size (you will get the error: 'Upgrade are failed!' if you try) so you will need to flash the mini version of DD-WRT onto the router BEFORE flashing the std or voip versions. Thus, the following page may be of more use to WRT54G v4.0 owners than the information below. The wiki page for Linksys WRT54GL is much more current than this one as of this writing. It is widely believed that the Linksys WRT54GL is exactly the same as the WRT54G v4.0. Until someone qualified to do so turns up knowing it needs to be done and willing to do it, The following information and workaround may be helpful:ДD-WRT v23 is obsolete, thus so is most of the information in this wiki page. This page needs to be brought up to date and cleaned up.

Reset your computer ethernet connection to auto IP and auto DNS.

CISCO LINKSYS WRT54GH FIRMWARE DOWNLOAD PASSWORD

To log into dd-wrt, use username root, password admin.

At this point you can choose to put a different build on, depending on what you needs are.

When you can again access the dd-wrt webgui using a browser at 192.168.1.1, do another HARD reset on the router.

When you can access the dd-wrt webgui using a browser at 192.168.1.1, power cycle the router.

Try using a different browser as well, to navigate to 192.168.1.1. If you still don't get success, clear your browser cache.

If you don't get success, repeat from steps 6 up to this one.

CISCO LINKSYS WRT54GH FIRMWARE DOWNLOAD FULL

When you get a success, wait FIVE FULL minutes.

Navigate to the folder that you are using, and select dd-wrt.v24_mini_generic.bin.

CISCO LINKSYS WRT54GH FIRMWARE DOWNLOAD UPGRADE

Go to administration and firmware upgrade.

Leave the username blank and enter 'admin' as the password.

If you see management mode, power cycle the router again.

You should open the linksys webgui and NOT a page that says Management Mode.

Open your browser to 192.168.1.1 by putting that in the browser address window of your browser.

Power cycle the router (uplug the power from the router for 30 seconds and then plug it back in).

Turn your firewall and any wireless computer connections OFF. Nothing should be connected to your computer or the router except the lan cable between them.

Connect the lan cable from your computer to a LAN port of your router.

Set a static IP on your computer to 192.168.1.7.

Do a HARD reset on the router according to note 1 of the peacock announcement (30/30/30).

Read the peacock announcement found here:.

The stock firmware from Linksys on the WRT54G v4 won't accept a firmware image over 3MB in size (you will get the error: 'Upgrade are failed!' if you try) so you will need to flash the mini version of DD-WRT onto the router BEFORE flashing any other versions. If you use an older version, you will need to Recover from a Bad Flash. WARNING: Only DD-WRT v23 and newer will run on this model. NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Cisco linksys wrt54gh firmware download